GATE 2021 Petroleum Engineering Previous Year Paper
GATE 2021 Petroleum Engineering Previous Year Paper
General Aptitude (GA)
Q.1 – Q.5 Multiple Choice Question (MCQ), carry ONE mark each (for each wrong answer: – 1/3).
Q.1
The current population of a city is 11,02,500. If it has been increasing at the rate of 5% per annum, what was its population 2 years ago?
(A)
9,92,500
(B)
9,95,006
(C)
10,00,000
(D)
12,51,506
Q.2
(A)
3
(B)
7
(C)
9
(D)
11
Q.3
The least number of squares that must be added so that the line P-Q becomes the line of symmetry is____________
(A)
4
(B)
3
(C)
6
(D)
7
Q.4
Nostalgia is to anticipation as ____ is to_________Which one of the following options maintains a similar logical relation in the above sentence?
(A)
Present, past
(B)
Future, past
(C)
Past, future
(D)
Future, present
Q.5
Consider the following sentences:I woke up from sleep.I woked up from sleep.I was woken up from sleep.I was wokened up from sleep.Which of the above sentences are grammatically CORRECT?
(A)
(i) and (ii)
(B)
(i) and (iii)
(C)
(ii) and (iii)
(D)
(i) and (iv)
6 – Q. 10 Multiple Choice Question (MCQ), carry TWO marks each (for each wrong answer: – 2/3).
Q.6
Given below are two statements and two conclusions. Statement 1: All purple are green.Statement 2: All black are green. Conclusion I: Some black are purple. Conclusion II: No black is purple.Based on the above statements and conclusions, which one of the following options is logically CORRECT?
(A)
Only conclusion I is correct.
(B)
Only conclusion II is correct.
(C)
Either conclusion I or II is correct.
(D)
Both conclusion I and II are correct.
Q.7
Computers are ubiquitous. They are used to improve efficiency in almost all fields from agriculture to space exploration. Artificial intelligence (AI) is currently a hot topic. AI enables computers to learn, given enough training data. For humans, sitting in front of a computer for long hours can lead to health issues.Which of the following can be deduced from the above passage?Nowadays, computers are present in almost all places.Computers cannot be used for solving problems in engineering.For humans, there are both positive and negative effects of using computers.Artificial intelligence can be done without data.
(A)
(ii) and (iii)
(B)
(ii) and (iv)
(C)
(i), (iii) and (iv)
(D)
(i) and (iii)
Q.8
Consider a square sheet of side 1 unit. In the first step, it is cut along the main diagonal to get two triangles. In the next step, one of the cut triangles is revolved about its short edge to form a solid cone. The volume of the resulting cone, in cubic units, is________________
(A)
𝜋/3
(B)
2𝜋/3
(C)
3𝜋2
(D)
3π
Q.9
The number of minutes spent by two students, X and Y, exercising every day in a given week are shown in the bar chart above.The number of days in the given week in which one of the students spent a minimum of 10% more than the other student, on a given day, is
(A)
4
(B)
5
(C)
6
(D)
7
Q.10
Corners are cut from an equilateral triangle to produce a regular convex hexagon as shown in the figure above.The ratio of the area of the regular convex hexagon to the area of the original equilateral triangle is
(A)
2 : 3
(B)
3 : 4
(C)
4 : 5
(D)
5 : 6
Petroleum Engineering (PE)
Q.1 – Q.13 Multiple Choice Question (MCQ), carry ONE mark each (for each wrong answer: – 1/3).
Q.1
MOPU (in the context of offshore drilling and production systems) stands for
(A)
Mobile Offshore Process Unit
(B)
Mobile Offshore Piping Unit
(C)
Mobile Offshore Production Unit
(D)
Mobile Oil Production Unit
Q.2
Which ONE of the following statements is INCORRECT?
(A)
Conductor is the outer casing of a well
(B)
Riser is used for transporting fluid
(C)
Conductor and riser have the same functions
(D)
Conductor is used for shielding the well flow lines from external forces
Q.3
Which ONE of the following offshore installations uses Dynamic Positioning System (DPS) for station keeping?
(A)
Jacket
(B)
Jack-up
(C)
Semi-submersible
(D)
Tension Leg Platform
Q.4
Which ONE of the following is NOT a primary safety system for offshore installations?
(A)
Emergency Shut Down
(B)
Isolation
(C)
Fire Protection
(D)
Blowdown
Q.5
The primary function of the thruster in the Dynamic Positioning System (DPS) of an offshore installation is
(A)
To apply thrust in the direction opposite to the resultant environmental force
(B)
To apply thrust in the same direction as the resultant environmental force
(C)
To apply thrust in the direction opposite to the motion
(D)
To apply thrust in the same direction as the motion
Q.6
Select the CORRECT firefighting system for electrical switchgear room in an offshore facility.
(A)
Wet chemical
(B)
Halon system
(C)
Foam
(D)
Water sprinklers
Q.7
Which ONE of the following options can be used to quantify secondary porosity?
(A)
Sonic and Gamma Ray Logs
(B)
Sonic and Neutron Logs
(C)
Sonic and Caliper Logs
(D)
Density and Neutron Logs
Q.8
Among the options given below, what is the typical temperature range for significant oil generation in a source rock associated with conventional crude-oil reservoirs?
(A)
10 oC – 40 oC
(B)
60 oC – 175 oC
(C)
225 oC – 325 oC
(D)
350 oC – 425 oC
Q.9
In the original Darcy’s law as proposed by Henry Darcy, which of the following drives the fluid flow through a fully saturated sand column?
(A)
Pressure-gradient or hydraulic-gradient
(B)
Viscous force per unit volume
(C)
Capillary force per unit volume
(D)
Inertial force per unit volume
Q.10
At which ONE of the following scales is Darcy’s law for fluid flow through a porous medium applicable?
(A)
Nano-scale
(B)
Molecular-scale
(C)
Microscopic-scale
(D)
Macroscopic-scale
Q.11
Pressure – Temperature phase diagram of CO2 is shown below. Identify the correct phases from the given options.
(A)
I = Solid Phase, II = Liquid Phase, III = Gas Phase, IV = Supercritical Phase
(B)
I = Gas Phase, II = Supercritical Phase, III = Solid Phase, IV = Liquid Phase
(C)
I = Supercritical Phase, II = Liquid Phase, III = Solid Phase, IV = Gas Phase
(D)
I = Gas Phase, II = Solid Phase, III = Liquid Phase, IV = Supercritical Phase
Q.12
A measure of the potential of crude oil to form surfactants for Enhanced Oil Recovery (EOR) is given by the Total Acid Number (TAN). TAN is the mass of _________(in milligrams) that is required to neutralize one gram of crude oil.
(A)
Ca(OH)2
(B)
NaCl
(C)
KOH
(D)
NaOH
Q.13
In Water-Alternating-Gas (WAG) injection, the purpose of the injection is to_____I _____ the “relative permeability” of gas and to _____ II _____ the “mobility” of the gas.
(A)
I = reduce, II = enhance
(B)
I = reduce, II = reduce
(C)
I = enhance, II = reduce
(D)
I = enhance, II = enhance
Q.14 – Q.19 Multiple Select Question (MSQ), carry ONE mark each (no negative marks
Q.14
Solids that may possibly form in the offshore pipelines during the production of oil and gas from deep-water reservoirs are
(A)
Wax
(B)
Char
(C)
Hydrates
(D)
Asphaltenes
Q.15
Oil and gas pipelines, which are at an elevated pressure (about 3 MPa) and sub-ambient temperature (below 298 K), may get blocked by the formation of solid hydrates. One of the strategies adopted to inhibit the formation of hydrates is the injection of Thermodynamic Hydrate Inhibitors (THIs) into the reservoir fluid.Identify all suitable chemicals that are commonly used as THIs.
(A)
Sodium Chloride
(B)
Methanol
(C)
Polyvinylpyrrolidone
(D)
Sodium Dodecyl Sulphate
Q.16
When CO2 and liquid water are brought in contact with each other, they may form solid hydrates. The three-phase hydrate boundary is shown in the Pressure -Temperature plot given below.Identify the correct statements.G = Gas
Phase, H = Hydrate Phase, L = Liquid Phase
(A)
Hydrates are stable in region I
(B)
Hydrates are stable in region II
(C)
Hydrates are stable in region III
(D)
Hydrates are stable in region IV
Q.17
Heavy oil recovered from reservoirs can be represented by CXH1.5X. Suitable processes to reduce the density of heavy oil are
(A)
Carbon Rejection
(B)
Pyrolysis
(C)
Hydrogenation
(D)
Filtration
Q.18
Identify the CORRECT statements for a 𝒏 × 𝒏 matrix.
(A)
Under elementary row operations, the rank of the matrix remains invariant
(B)
Under elementary row operations, the eigenvalues of the matrix remain the same
(C)
If the elements in a row can be written as a linear combination of two or more rows, then the matrix is singular.
(D)
The rank of the matrix is equal to 𝑛 if the determinant of the matrix is zero.
Q.19
During a drilling operation, kick occurs if
(A)
the shear ram in the Blow Out Preventer (BOP) does not work.
(B)
the formation pressure is equal to the drilling fluid pressure.
(C)
the volume of the mud used to fill the hole is less than that of the pipe being pulled out.
(D)
the formation pressure is more than the drilling fluid pressure.
Q.20 – Q.25 Numerical Answer Type (NAT), carry ONE mark each (no negative marks).
Q.20
The value of is_________(correct up to one decimal place).
Q.21
Given two complex numbers, 𝒛𝟏 = 𝟒 + 𝟑𝒊 𝐚𝐧𝐝 𝒛𝟐 = 𝟐 − 𝟓𝒊, the real part of (𝒛𝟏𝒛̅̅𝟐̅) is .
Q.22
The number of ‘three-digit numbers’ that can be formed using the digits from 1 to 9 without the repetition of each digit is .
Q.23
The estimate for the root of the function 𝒇(𝒙) = 𝒆𝟐𝒙 + 𝟐𝒙 after one iteration with an initial guess of 𝒙𝟎 = 𝟎, using the Newton-Raphson method is__________(correct up to two decimal places).
Q.24
A saturated oil reservoir has an average reservoir pressure of 3000 psia, tested for flowing bottom-hole pressure (BHP) of 2000 psia and production rate of 500 STB/day. The maximum reservoir deliverability based on Vogel’s equation for two-phase flow is_____________STB/day.
Q.25
If the specific heat ratio of natural gas is 1.28, the critical pressure ratio (ratio of outlet pressure to upstream pressure) through a choke is_____(round off to two decimal places).
Q.26 – Q.37 Multiple Choice Question (MCQ), carry TWO mark each (for each wrong answer: – 2/3)
Q.26
Match the suitable artificial lift methods (GROUP I) to meet the requirements (GROUP II) given in the table.
(A)
P – I, Q – II, R – IV, S – III
(B)
P – II, Q – I, R – IV, S – III
(C)
P – I, Q – II, R – III, S – IV
(D)
P – II, Q – I, R – III, S – IV
Q.27
Match the Enhanced Oil Recovery (EOR) methods (GROUP I) with the corresponding laboratory tests (GROUP II)
(A)
P – III, Q – II, R – I, S – IV
(B)
P – II, Q – IV, R – I, S – III
(C)
P – III, Q – IV, R – II, S – I
(D)
P – III, Q – II, R – IV, S – I
Q.28
Identify the following well test methods corresponding to the transient pressure profiles in the figures given below. (BHP: Bottom-hole pressure, BOPD: Barrels of oil per day)Flow-after-flow testInterference testFall-off testModified isochronal test (I) (II)
(III) (iv)
(A)
P – IV, Q – II, R – I, S – III
(B)
P – II, Q – III, R – IV, S – I
(C)
P – II, Q – III, R – I, S – IV
(D)
P – IV, Q – I, R – III, S – II
Q.29
Match the following wire-line logging methods (GROUP I) based on the physical principles of measurements (GROUP II).
(A)
P – II, Q – I, R – IV, S – III
(B)
P – III, Q – I, R – IV, S – II
(C)
P – III, Q – II, R – IV, S – I
(D)
P – II, Q – I, R – III, S – IV
Q.30
Match the following rock types (GROUP I) with their respective chemical compositions (GROUP II) from the given options.
(A)
P – III, Q – II, R – IV, S – I
(B)
P – II, Q – III, R – I, S – IV
(C)
P – III, Q – I, R – IV, S – II
(D)
P – III, Q – I, R – II, S – IV
Q.31
The following equations describe the transient fluid flow in a typical petroleum reservoir system. Here, 𝒑 is pressure, 𝒙 𝐚𝐧𝐝 𝒓 𝐚𝐫𝐞 𝐭𝐡𝐞 spatial coordinates in rectangular and cylindrical systems respectively, 𝐚𝐧𝐝 𝒕 is time. Also,𝝓 (𝐩𝐨𝐫𝐨𝐬𝐢𝐭𝐲), 𝝁 (𝐯𝐢𝐬𝐜𝐨𝐬𝐢𝐭𝐲),𝒄𝒇(𝐟𝐨𝐫𝐦𝐚𝐭𝐢𝐨𝐧 𝐜𝐨𝐦𝐩𝐫𝐞𝐬𝐬𝐢𝐛𝐢𝐥𝐢𝐭𝐲), 𝒄𝒕(𝐭𝐨𝐭𝐚𝐥 𝐜𝐨𝐦𝐩𝐫𝐞𝐬𝐬𝐢𝐛𝐢𝐥𝐢𝐭𝐲) 𝐚𝐧𝐝 𝒌(𝐩𝐞𝐫𝐦𝐞𝐚𝐛𝐢𝐥𝐢𝐭𝐲) are constant coefficients.Match the equations (GROUP I) with their corresponding descriptions (GROUP II).
(A)
P – IV, Q – I, R – II, S – III
(B)
P – IV, Q – III, R – II, S – I
(C)
P – III, Q – IV, R – II, S – I
(D)
P – III, Q – IV, R – I, S – II
Q.32
Select the INCORRECT statement related to Enhanced Oil Recovery (EOR) techniques from the following options.
(A)
Alkaline flooding recovers crude oil by reduction of interfacial tension (IFT) and reversal of wettability of rocks.
(B)
In-situ combustion recovers crude oil by the application of heat, thus lowering the viscosity of the crude oil.
(C)
Nitrogen flue gas flooding recovers crude oil by vaporizing the lighter components of the crude oil.
(D)
Polymer flooding recovers crude oil by reducing the viscosity and increasing the mobility of water.
Q.33
Match the petroleum reservoir forming traps (GROUP I) with their general classifications (GROUP II).
(A)
P – III, Q – II, R – IV, S – I
(B)
P – II, Q – III, R – IV, S – I
(C)
P – III, Q – I, R – II, S – IV
(D)
P – II, Q – III, R – I, S – IV
Q.34
An Ideal Pressure Buildup Test yields a single straight line for all times, where shut-in Bottom-Hole Pressure (Pws) is plotted against 𝐥𝐨𝐠𝟏𝟎. Here 𝒕𝒑 is the well production time and 𝚫𝒕 is the time elapsed since shut-in. However, in an actual Pressure Buildup Test, a non-linear curve is obtained which can be logically divided into distinct regions.Choose the INCORRECT option from the following.
(A)
A late-time region, in which the radius of investigation has reached the well’s drainage boundaries.
(B)
A middle-time region during which the pressure transient has moved away from the wellbore and into the bulk formation.
(C)
An early-time region during which a pressure transient is moving through the formation nearest the wellbore.
(D)
An early-time region during which a pressure transient is moving away from the drainage boundary.
Q.35
When two immiscible fluid phases are placed in contact with a solid surface, one phase usually is attracted to solid more strongly than the other phase.The more strongly attracted phase is called the ‘wetting phase’.The inter-molecular interaction of the non-wetting phase with the solid is_____I than its intra-molecular interaction. Due to this, the non-wetting phase tends to occupy the II of the reservoir.
(A)
I = stronger, II = smaller pores
(B)
I = stronger, II = larger pores
(C)
I = weaker, II = smaller pores
(D)
I = weaker, II = larger pores
Q.36
Coal bed methane is methane gas adsorbed in coal seams. To desorb the methane from the coal seam it should be exposed to CO2 and (or) N2. Which ONE of the following is an appropriate reason to enhance the desorption process?
(A)
N2 is used because it has low kinetic energy compared to CH4
(B)
CO2 is used as it has high kinetic energy compared to CH4
(C)
CO2 is used as it strongly binds with coal compared to CH4
(D)
N2 is used as it strongly binds with coal compared to CH4
Q.37
Match the platforms (GROUP I) with appropriate support systems (GROUP II).
(A)
P – IV, Q – III, R – I, S – II
(B)
P – II, Q – III, R – I, S – IV
(C)
P – III, Q – I, R – IV, S – II
(D)
P – I, Q – IV, R – II, S – III
Q.38 – Q.39 Multiple Select Question (MSQ), carry TWO mark each (no negative marks).
Q.38
Select the CORRECT statements from the following. Well testing operations on a typical crude oil reservoir
(A)
do not measure rock and fluid properties of the reservoir when the well is flowing or shut-in.
(B)
measure variation in pressure response of the reservoir with time when the well is flowing or shut-in.
(C)
measure productivity index and partial well completion.
(D)
do not measure length and conductivity of hydraulic fractures.
Q.39
Crude oil from oil sands contains bitumen and asphaltene and this crude is heavy and viscous at room temperature. Assume that one such crude oil is represented by CXH1.2XOY. For easier transportation through pipelines it should be processed further. Identify the processes which help in transportation of this crude oil.
(A)
Drying
(B)
Vis-breaking
(C)
Coking process
(D)
Hydro-treating
Q.40 – Q.55 Numerical Answer Type (NAT), carry TWO mark each (no negative marks).
Q.40
Given matrix 𝑨 =. The eigenvalue corresponding to the eigenvectoris ______________ .
Q.41
The maximum value of the function 𝒇(𝒙) = 𝒙𝟒 − 𝟖𝒙𝟐 + 𝟐 for −𝟐 ≤ 𝒙 ≤ 𝟐 is_______.
Q.42
Given the second order ordinary differential equation: 𝒚′′ + 𝟑𝒚′ − 𝟒𝒚 = 𝟎 with the initial conditions 𝒚(𝟎) = 𝟑, 𝐚𝐧𝐝 𝒚′(𝟎) = −𝟕, the value of y(1) is________(round off to two decimal places).
Q.43
The directional derivative of 𝒇(𝒙, 𝒚, 𝒛) = 𝒙𝟐 + 𝟑𝒚𝟐 + 𝒛𝟐, at point (2,1,0) along the unit vector in x-direction, 𝒊̂, is __.
Q.44
A productivity test conducted on a crude oil well indicates a stabilized flow rate of 150 STB/day (water-free oil production) at a bottom-hole flowing pressure of 935 psig. After shutting the well for 24 hours, the bottom-hole pressure reached a static value of 1250 psig.The Absolute Open Flow (AOF) potential of the well is__________STB/day.
Q.45
A porous medium (shown schematically in the figure) has the following properties.Length L = 600 m, Width W = 8 m, Height h = 0.5 m, Permeability k = 100 mD, Porosity ϕ = 15%. An incompressible fluid having a viscosity of 2 cP is flowing through a porous medium at the inlet and exit pressures of 7 × 106 Pa and 6 × 106 Pa, respectively.The actual fluid velocity through the porous medium is × 10-7 m/s. (1 Darcy = 10-12 m2)
Q.46
A tubing with an inner diameter of 2.259 inch delivers oil from a well at the rate of 1000 bbl/day. The API gravity and viscosity of the oil are 40o and 1.2 cP, respectively. The tubing makes an angle of 15o with the vertical. Assuming a fanning friction factor of 0.006, the pressure-drop over a length of 1000 ft tubing is ______ psi (round off to nearest integer).[1 bbl = 5.615 ft3]
Q.47
A cylindrical crude oil reservoir with a radius of 3000 ft is under water influx from a cylindrical aquifer with an estimated radius of 9000 ft. The reservoir has the following properties.Aquifer thickness, h = 40 ft Porosity, ϕ = 15%Formation compressibility, Cf = 4.5 × 10-6 psi-1 Water compressibility, Cw = 4.0 × 10-6 psi-1Assuming a pot reservoir model with fractional encroachment angle as unity, the water influx into the reservoir for a pressure drop of 700 psi is ________MMbbl (million barrels) (round off to two decimal places).(π = 3.14, 1 bbl = 5.615 ft3)
Q.48
A heavy oil reservoir with an initial oil recovery of 10% has the following properties.Confined area A = 1.5 acres, thickness of the reservoir h = 15 ft, effective porosity ϕ = 15%, irreducible water saturation Swr = 25%, oil formation volume factor Bo = 1.10 bbl/STB.An in-situ combustion test was conducted in the above reservoir. Oil recovery due to the combustion process at the well is observed to be 12000 bbl.The total (overall) oil recovery at the end of the in-situ combustion process is__________% (round off to nearest integer) of the original oil in place.(1 acre = 43560 ft2, 1 bbl = 5.615 ft3)
Q.49
A double acting duplex pump with a rod diameter of 2.5 inch and a stroke of 20 inch is to be operated at 60 strokes per minute for drilling down to 10000 ft. The flow rate is 600 gpm. If the volumetric efficiency of the pump is 80%, the liner size is _________inch (round off to one decimal place).[1 gallon = 231 inch3]
Q.50
The fluid flow through an under-saturated oil reservoir is driven by solution gas drive mechanism. The reservoir parameters are as given below.Compressibility of water, 𝒄𝒘 = 𝟏 × 𝟏𝟎−𝟔 psi-1 Compressibility of formation, 𝒄𝒇 = 𝟏 × 𝟏𝟎−𝟓 psi-1 Connate water saturation, 𝑺𝐰𝐜 = 𝟎. 𝟐Initial reservoir pressure, 𝒑𝒊 = 𝟒𝟎𝟎𝟎 psiReservoir pressure at bubble-point, 𝒑𝐛 = 𝟑𝟎𝟎𝟎 psi Oil formation volume factor, 𝑩𝐨𝐢 = 𝟏. 𝟐𝟒 rb/STBFormation volume factor at bubble point pressure, 𝑩𝐨𝐛 = 𝟏. 𝟐𝟔 rb/STB.The percentage of oil recovered as a fraction of the Original Oil in Place (OOIP) is ___________% (round off to one decimal place).
Q.51
During drilling, a well is damaged out to a radial distance of 5 ft from the periphery of the wellbore so that the permeability within the damaged zone is reduced to 1/50th of the undamaged effective permeability. After completion, the well is stimulated so that the permeability out to a radial distance of 15 ft from the periphery of the wellbore is increased to twenty times the permeability of the undamaged zone.The radial inflow equation for stabilized flow conditions under semi-steady state conditions is given by where 𝒑𝐞 is effective pressure, 𝒑𝐰𝐟 is flowing bottom-hole pressure, 𝒒 is flow- rate, 𝝁 is viscosity, 𝒌𝐞 is average effective permeability, 𝒉 is reservoir thickness, 𝒓𝐞 is drainage radius, 𝒓𝐰 is wellbore radius and 𝑺 is skin factor.If 𝒓𝐰 = 𝟎. 𝟓 ft and 𝒓𝐞 = 𝟓𝟎𝟎 ft, then the increase in Productivity Index ratio is (round off to one decimal place).
Q.52
A depleted and shut-in oil reservoir originally contained 𝟐𝟓 × 𝟏𝟎𝟔 STB of oil with a formation volume factor of 1.35 res bbl/STB and a connate water saturation of 0.25. Cumulative oil production to date has been 𝟐. 𝟓 × 𝟏𝟎𝟔 STB of oil. The oil formation volume factor is now 1.25 res bbl/STB. Assuming no water influx, the gas saturation in the reservoir is _______% (round off to one decimal place).
Q.53
Surface tension of liquid A in a capillary is being measured in the laboratory using capillary rise (refer the figure given below). The capillary radius (r) is 100 µm, the height of liquid column (h) is 10 cm and Ө = 38o. Density of air can be neglected. Assume liquid A to have the same density as water.Surface tension of liquid A at room temperature is ___________________dynes/cm (round off to one decimal place).
Q.54
Miscible displacement process is one of the EOR techniques. The performance of this process depends on fluid physical properties that affect flow behavior in a reservoir. Two of the important properties are density and viscosity.Consider the use of CO2 for one such process. The density of CO2 at the reservoir condition is lb/ft3 (round off to one decimal place).Relevant data for this calculation are given below. Reservoir temperature = 300 oF (422 K) Reservoir pressure = 1470 psig (100 atm)Compressibility factor (z) at the reservoir condition = 0.5Values of Universal Gas Constant (R) in different units are listed below. Universal Gas Constant (R) = 8.314 m3.Pa.K-1mol-1= 10.731 psi. ft3.lb. mol-1 oR-1= 0.082 L. atm. K-1 mol-1
Q.55
In a counter current heat exchanger, the hot fluid enters at 175 oF and exits at 100 oF. The cold fluid enters at 75 oF and exits at 85 oF. For the calculation of heat transfer rate, consider the tube surface area (per unit length) to be 0.26 ft2/ft and a tube length of 40 ft. The overall heat transfer coefficient of the exchanger is 100 BTU/hr-ft2. The minimum number of tubes required in the exchanger for a heat duty of 𝟏𝟓 × 𝟏𝟎𝟓 BTU/hr is _______(round off to nearest integer).
Q.1
is_________(correct up to one decimal place).
. Here 𝒕𝒑 is the well production time and 𝚫𝒕 is the time elapsed since shut-in. However, in an actual Pressure Buildup Test, a non-linear curve is obtained which can be logically divided into distinct regions.Choose the INCORRECT option from the following.
. The eigenvalue corresponding to the eigenvector
is ______________ .
where 𝒑𝐞 is effective pressure, 𝒑𝐰𝐟 is flowing bottom-hole pressure, 𝒒 is flow- rate, 𝝁 is viscosity, 𝒌𝐞 is average effective permeability, 𝒉 is reservoir thickness, 𝒓𝐞 is drainage radius, 𝒓𝐰 is wellbore radius and 𝑺 is skin factor.If 𝒓𝐰 = 𝟎. 𝟓 ft and 𝒓𝐞 = 𝟓𝟎𝟎 ft, then the increase in Productivity Index ratio is (round off to one decimal place).
